JWD1-6T Screw Type Switching TB for Breaking Capacity

Inquire Now

Share:

Product Description
Parameters
Certification

Terminal thickness: 8 Miniature current terminal
Rigid conductor	Flexible conductor		I		Ui
(mm²)			(A)		(V)
0.2-10	0.2-6		57		500
IEC 60947-7-1
Type		Part Number		Package quantity

Description		Schematic diagram	Type
Test terminal:			JWD1-6T
With general-purpose locating base, suitable for standard mounting rails
and

Switching terminal:
With general-purpose locating base, suitable for standard mounting rails
and

(1) End plate:
One additional piece must be attached to the end of each terminal strip set. If it is mounted in the center of the terminal strip, the creepage distance may increase.
(2) Central liaison part:			JWD9-ZL 8/2
It is used to connect terminals with the same specification and form a liaison terminal group; each part has 10 digits (supplied with screws) that can be further divided at will.			JWD9-ZL 8/3
			JWD9-ZL8/4
			JWD9-ZL8/10
(3) Edge liaison part	2 digits:		JWD9-BL 8/2
Its role is the same as that of the central liaison part (2); with insulation on the back side; 10 digits that can be further divided at will			JWD9-BL 8/3
			JWD9-BL8/4
			JWD9-BL8/10
	3 digits:
	10 digits:
(4) Divider:
It is used to separate two adjacent liaison terminal groups and can be inserted after assembly, without any effect on the overall space.
(5) Group partition:
Used for separation of each terminal group; with dual effects (visible grouping and electrical isolation)
(6) Central liaison part			JWD9-LJ 8/2
It is used to connect terminals with the same specification and form a liaison terminal group; each part has 10 digits (supplied with screws) that can be further divided at will.
(7) Switch liaison part
It can be used on both sides of the breaking sliding block for two terminals; the strap of the liaison part is pushed inwards to make it break; two screws are supplied.
(8) Switch liaison part
It can be used on both sides of the breaking sliding block for two terminals; the strap of the liaison part is pushed outwards to make it break; two screws are supplied.
(9) Switch liaison part
It is used for two terminals; please note that it can only be used on the right of terminals; two screws are supplied.
(10) Switch liaison part
It is used for the short circuit of a three-phase interconnected current transformer and can only be used on the right of the terminal; 1) four screws are supplied.
(11) Test plug:			ZP9.5/8-10
(12) Conversion test plug:
(13) Tag:

Terminal dimensions
Thickness / width / end plate thickness		[mm]	8/51.2/-
Height (TH 35:7.5 / TH 35:15 / G 32:15)		[mm]	46/53.5/-
Technical data based on IEC/DIN VDE standards
Maximum rated working current / cross-sectional area		[A]/ [mm]	Jun-57
Maximum cross-sectional area of conductors (rigid / flexible) that can be connected if any edge liaison part is used		[mm2]	6月6日
Rated impulse withstand voltage / degree of pollution		[kV]/-	6月3日
Over-voltage category / insulation material group		-/-	lll/l
Connection capacity
Flexible conductor with tubular bare terminal / tubular pre-insulated terminal		[mm2]	0.5-6/0.5-4
Connection of multiple conductors (connecting two conductors with the same cross-sectional area)
Rigid conductor / flexible conductor		[mm2]	0.5-2.5/0.5-6
Flexible conductor with tubular bare terminal		[mm2]	0.5-4
Flexible conductor with DEV-tubular pre-insulated terminal		[mm2]	0.5^
Stripping length		[mm]	12
Screw for terminal position: screw / torque		[Nm]	M4/1.5-1.8
Screw for breaking sliding block: screw / torque		[Nm]	-
Insulation material type			PA
Material flammability according to UL94			V0
Rated working voltage / rated working current / wire gauge	UL:[V]/[A]/AWG		300/50/26-8