JWD1-2.5/2 Screw Type double layer Din-Rail TB

The double-layer terminal has the double connection capacity in the same spatial position compared to the basic-type terminal. This plays a crucial role in the applications where the connection space is limited.
In terms of design, there is a 2.5 mm space between the upper and lower layers of the double-layer terminal. This provides a well-arranged hierarchical structure. Besides, in case of full connection in the upper layer, this can also facilitate connection with screwdriver in the lower layer of the terminal, with clear identification; after a compensating end plate is mounted, the terminal locating and fastening of the terminal strip or the assembly of other types of terminals will not be affected, and orderly arrangement can be ensured.
The double-layer interconnected terminal can connect multiple conductors to one terminal in order to achieve "potential distribution" or due to a loop branch. This avoids the need for adjacent arrangement of multiple terminal groups and for electric connection via a central liaison part because both solutions will increase the installation space and costs.

The yellow-green closed-end insulating housings of the double-layer ground terminal has the same configuration as the double-layer terminal, so their compatible adjacent arrangement is possible.

Inquire Now

Share:

Product Description
Parameters
Certification

Terminal thickness: 5.2
	Rigid conductor	Flexible conductor	I	Ui
	(mm²)		(A)	(V)
IEC 60947-7-1	0.2-4	0.2-2.5	24	500

Description		Color	Schematic diagram	Type	Part Number	Package quantity
Terminal: With general-purpose locating base, suitable for standard mounting rails and		Grey		JWD1-2.5/2	5 574 193	60
		Blue		JWD1-2.5/2 BU	5 574 194	60
Top and bottom interconnected terminals: The mounting and use methods are the same as above; the conducting plates in the upper and lower layers are interconnected to achieve the same potential of top and bottom connecting points.		Grey
		Blue
(1) End plate: (thickness: 2.5) One additional piece must be attached to the end of each terminal strip set. If it is mounted in the center of the terminal strip, the creepage distance may increase.		Grey		2.5-4/2 G	8 050 110	50
		Blue		2.5-4/2 G BU	8 050 111	50
(2) Compensating end plate: (thickness: 2.5) It is used to offset interlayer displacement while it is adjacent to an ordinary terminal.		Grey		2.5-4/2BD	8 053 101	50
		Blue		2.54/2BD BU	8 053 102	50
(3) Compensating end plate: (thickness: 2.5) It is used for terminal locating and fastening of the terminal strip or for offsetting interlayer displacement while it is arranged with other terminals in the same group.				2.5-4/2 BD-1	8 053 105	50
(4) Central liaison part: It is used to connect terminals with the same specification and form a liaison terminal group; each part has 10 digits (supplied with screws) that can be further divided at will.				ZLB5/10	5 585 310	50
(5) Connecting sheet: For central connection of more than 10 digits				LJ 5/2	5 583 102	100
(6) Edge liaison part: Its role is the same as that of the central liaison part (4); with insulation on the back side; 10 digits that can be further divided at will	2 digits:			BL5/2	5 582 112	200
	3 digits:			BL5/3	5 582113	200
	10 digits:			BL5/10	5 582 120	100
(7) Jumping liaison part: With the spacer (8), it can connect any non-adjacent terminals in the center to form a jumping liaison terminal group.				KL5/10	5 584 120	50
(8) Spacer: Used as a spacer block between the accessory of the jumping liaison part (7) and the conductive part of the terminal				KB5	8 510 105	2000
(9) Divider: It is used to separate two adjacent liaison terminal groups and can be inserted after assembly, without any effect on the overall space.				GP-1	8 751 102	500
(10) Group partition: (thickness: 2.5) Used for separation of each terminal group; with dual effects (visible grouping and electrical isolation)				2.5-4/2 GF	8 750 108	50
(11) Tag:				ZP5	8 868102	100
Terminal dimensions
Thickness / width / end plate thickness			[mm]	5.2/56/2.5
Height (TH 35:7.5 / TH 35:15 / G 32:15)			[mm]	62/69.5/67
Technical data based on IEC/DIN VDE standards
Maximum rated working current / cross-sectional area			[A] / [mm²]	32/4
Maximum cross-sectional area of conductors (rigid / flexible) that can be connected if any edge liaison part is used:			[mm²]	2.5/2.5
Rated impulse withstand voltage / degree of pollution			[kV]/-	6/3
Over-voltage category / insulation material group			-/-	lll/l
Connection capacity
Flexible conductor with tubular bare terminal / tubular pre-insulated terminal			[mm²]	0.25-2.5 / 0.25-1.5
Connection of multiple conductors (two conductors with the same cross-sectional area)
Rigid conductor / flexible conductor			[mm²]	0.2-1/0.2-1.5
Flexible conductor with tubular bare terminal			[mm²]	0.25-1.5
Flexible conductor with DEV-tubular pre-insulated terminal			[mm²]	0.5-1
Stripping length			[mm]	8
Screw type				M3
Torque			[Nm]	0.6-0.8
Insulation material type				PA
Material flammability according to UL94				V0
Rated working voltage / rated working current / wire gauge			UL:[V]/[A]/AWG	600/20/28-12
Note: When an edge liaison part is used, a cable below 1.5 mm² should be used for a 2.5 mm² terminal; corresponding cables should be used for terminals with other cross-sectional areas (mm²).