JWD1-1.5CG Screw Type three-layer sensor Din Rail TB
Inductive and capacitive three-wire sensors or actuators (such as solenoid valve and motor) have an increasingly broader range of applications in the machinery manufacturing field. Sensor and actuator terminals have the following advantages:
- Significantly lower connection costs by means of potential distribution;
- The edge bridgeware eliminates the need for screws and the time of screw tightening generally required by ordinary terminals;
- The terminals with luminous display are available as expected by customers. The on-off state can be displayed to facilitate troubleshooting;
- Sensor terminals have the same profiles as actuator terminals, so they can be mixed and adjacent to each other;
The terminals with LED are used for PNP or NPN control sensors.
Inductive and capacitive three-wire sensors or actuators (such as solenoid valve and motor) have an increasingly broader range of applications in the machinery manufacturing field. Sensor and actuator terminals have the following advantages:
– Significantly lower connection costs by means of potential distribution;
– The edge bridgeware eliminates the need for screws and the time of screw tightening generally required by ordinary terminals;
– The terminals with luminous display are available as expected by customers. The on-off state can be displayed to facilitate troubleshooting;
– Sensor terminals have the same profiles as actuator terminals, so they can be mixed and adjacent to each other;
The terminals with LED are used for PNP or NPN control sensors.
Terminal thickness: 6.2
Rigid conductor
Flexible conductor
I
Ui
(mm2)
(A)
(V)
Ratings
0.2-4
0.2-2.5
26
250*
Description
Color
Type
Terminal:
It can be mounted on the guide rail .
Grey
JWD1-1.5CG
Blue
JWD1-1.5CG BU
Terminal:
Same as above, but there is a red (RD) or green (GN) light emitting diode (LED) between the upper and middle layers.
15-30 DC
15-30 DC
Terminal:
Same as above, but there is a red (RD) or green (GN) light emitting diode (LED) between the upper and lower layers.
15-30 DC
15-30 DC
(1) Central liaison part:
It is used to connect terminals with the same specification and form a liaison terminal group; each part has 10 digits (supplied with screws) that can be further divided at will.
ZL6/10
Imax: 26A
(2) Edge liaison part:
Used for bridging between the middle and lower layers of the terminal; separable tooth back insulation
BL 6/2
BL 6/3
BL 6/10
(3) Quick tag:
10 digits; white
ZP6
Terminal dimensions
Thickness / width / end plate thickness
[mm]
6.2/55
Height (TH 35:7.5 / TH 35:15 / G 32:15)
[mm]
54.5/62
Technical data based on IEC/DIN VDE standards
Maximum rated working current / cross-sectional area
[A] / [mm2]
26/2.5
Maximum cross-sectional area of conductors (rigid / flexible) that can be connected if any edge liaison part is used:
[mm2]
4/2.5
Rated impulse withstand voltage / degree of pollution
[kV]/-
45385
Over-voltage category / insulation material group
-/-
lll/l
Connection capacity
Flexible conductor with tubular bare terminal / tubular pre-insulated terminal
[mm2]
0.25-2.5 / 0.25-2.5
Connection of multiple conductors (two conductors with the same cross-sectional area)
Rigid conductor / flexible conductor
[mm2]
0.2-1 /0.2-1
Flexible conductor with tubular bare terminal
[mm2]
0.25-1
Flexible conductor with DEV-tubular pre-insulated terminal
[mm2]
0.5-1
Stripping length
[mm]
8
Screw type
M3
Torque
[Nm]
0.6-0.8
Insulation material type
PA
Material flammability according to UL94
V0
Certification data (UL and CAS)
Rated working voltage / rated working current / wire gauge
